For a property preservation vendor, MCS is one of the biggest names in the business — and one of the most straightforward to understand once you know its one governing rule. MCS, short for Mortgage Contracting Services, works with mortgage servicers throughout the United States and its territories to protect, preserve, and maintain the properties those servicers are responsible for. Everything it assigns points at the same end goal: getting the property into conveyance condition.
That goal is what makes MCS work different from a one-off repair job. You are not fixing a house for a homeowner. You are bringing a property up to the standard the investor for that loan type requires, so the servicer can convey it — hand it over — cleanly. Learn the rule that governs each order, document the work the way a reviewer needs to see it, and MCS becomes steady, repeatable volume.
What MCS Is — and What It Is Not
Mortgage Contracting Services (mcs360.com) is a national property preservation company that works with mortgage servicers across the US and its territories. Its stated job is to make sure the properties servicers are responsible for are protected, preserved, and maintained in a manner that complies with the regulatory guidelines for the loan type, as well as any code compliance legislation for the area.
The work itself will feel familiar to any preservation vendor: secure the property, remove debris, conduct regular lawn maintenance, and winterize when necessary. MCS also lists a wider bench of services — discoloration remediation, eviction coordination, insurance claim repairs, pool securing and maintenance, roof repair and replacement, violation resolution, and steel security solutions such as A/C fortresses and steel window screens. But the core of the volume a field vendor sees is the standard preservation set: securing, debris, lawn, winterization, and snow removal.
The MCS Work Order Types Vendors Actually See
MCS publishes its standard preservation services, and they map directly onto the orders vendors receive. Know what each type authorises before you drive to the property — doing work an order does not authorise is the fastest way to do a job you cannot bill.
Conveyance Condition Management
This is the order type that explains MCS. It authorises all work required by the regulatory guidelines for each loan type so the property reaches conveyance condition. If work is needed to bring the property into conveyance condition and it can be completed per the published investor guidelines, it gets completed in conjunction with this work order. If the work cannot be completed per the published investor guidelines, an estimate is provided to bring the property into conveyance condition instead. That distinction — complete the work when the guidelines allow it, estimate when they do not — runs through every MCS order you will see. Our HUD conveyance condition guide explains what conveyance condition actually means in practice.
Securing Services
The initial secure is the order most vendors meet first. It authorises the services required by the applicable investor guidelines and/or client requirements — typically changing the entry lock(s) to the required key code, locking all windows and doors, winterizing to the applicable specifications, and maintaining the exterior grounds. MCS is explicit on one point: no additional property preservation will be completed in conjunction with a securing order unless specifically requested. Do the secure, document the secure, and stop there unless the order says otherwise. Our initial secure work order guide and lock change work orders guide cover the field detail.
Debris Removal
Debris orders authorise the removal of interior, exterior, and/or hazardous debris at each property, based on client requirements and/or the investor specifications for each loan type. Personals are handled per local municipality, law enforcement, investor/insurer guidelines, and client requirements — which means the rules for what you can remove, and how, change with the property. Photograph before you touch anything, and never assume a debris order covers personals.
Lawn Maintenance
Lawn orders cover mowing, weeding, edge trimming, sweeping paved areas — sidewalks, driveways, patios — and removal of all lawn clippings, related cuttings, and incidental debris. The purpose is practical: maintain the property’s appearance, prevent further degradation to the grounds, and relieve the property of any existing or potential violation of local ordinance. MCS also runs an automatic grass cut program, where grounds are maintained according to the applicable investor guidelines for each loan type until MCS is instructed to remove the property from the program. Recurring grass cuts are some of the steadiest volume in preservation — our grass cut work orders guide covers how to run them profitably.
Winterization and Snow Removal
Winterization orders authorise winterizing the plumbing at each property to prevent freeze damage, according to the investor requirements for each loan type. Snow removal is completed on walkways and driveways as needed to provide safe access to a property and per local municipality requirements. In November, these two order types surge — and winterization is often bundled inside a securing order, so a secure in freeze season is really two jobs in one visit. Our winterization work order checklist and snow removal work orders guide cover both in detail.
Other Preservation Services
Beyond the standard set, MCS lists discoloration remediation, eviction coordination, insurance claim repairs, pool securing and maintenance, roof repair and replacement, violation resolution, and steel security solutions. These are less frequent for a general field vendor, but they are where trade-licensed vendors — roofing, plumbing, HVAC, electrical — pick up higher-value MCS work.

The Investor-Guideline Rule: The One Rule That Governs Every MCS Order
If you remember one thing from this guide, remember this: on MCS work, the regulatory guidelines for the loan type govern. MCS says so plainly on its own services page. For loan types with no applicable regulatory guidelines, the HUD guidelines are followed instead.
In practice, that means three things for a vendor:
- Read the order’s guideline reference before you start. FHA, VA, USDA, and GSE loans each carry their own published investor guidelines, and the allowable scope follows the loan type, not your judgement of what the property needs.
- If the guidelines do not allow the work, estimate it — do not do it. When work needed to reach conveyance condition cannot be completed per the published investor guidelines, MCS’s own rule is to provide an estimate instead. A bid is the correct outcome in that case, not unauthorised work.
- Local code still applies. The guidelines govern the preservation scope; code compliance legislation for the area governs on top of them.
This is also why MCS work rewards vendors who keep their guideline references close. The vendor who knows which loan type the order belongs to bids accurately, works inside the authorised scope, and rarely hears back from a reviewer.
The MCS Work Order Lifecycle, Step by Step
Every MCS order follows the same path. Learn the sequence once and it becomes routine.
1. Accept the Order and Read the Scope
Read the order before you drive anywhere: scope, due date, address, loan type, and any client instructions or investor guidelines. Note which tasks are complete-and-bill and which need a bid first, which tasks need photos, and what the order authorises — and what it does not. On a securing order, remember the rule: no additional preservation unless specifically requested.
2. Do the Work and Photograph Everything
Do the work to the scope and to the investor guidelines, and photograph it the way a reviewer needs to see it: identification shot first, before shots from a wide angle, during shots showing the work happening, and after shots from the same position and angle as the before shots.
3. Complete the Documentation and Match It to the Photos
The property condition report and the invoice are part of the order, not optional paperwork. Before submission, organise the photos and match them to the tasks, make sure the report matches the photo evidence, and make sure the invoice matches the completed work. A report that says one thing and photos that show another is the most common reason a preservation order comes back — on MCS work as on every other national platform.
4. Submit Bids Where the Order Asks for Them
Some MCS orders are complete-and-bill; others need a bid before the work is approved — most notably when work needed for conveyance condition cannot be completed per the published investor guidelines. Bid real dimensions, not guesses from the listing photo, and photograph the measurement in frame. If two tasks are separate line items, bid them separately; bundling invites a reduction. Before you send a bid, run the numbers through our free property preservation job profit calculator — drive time, materials, and paperwork time included.
5. Mark the Order Complete Only When Everything Is In
Do not mark an order complete with items outstanding and plan to “send the rest later.” Submit the work, the photos, and the documentation together, in the system MCS assigned the order through, and only then close it out. An incomplete completion is a rejection waiting to happen.
6. Handle Rejections and QC Follow-Up the Same Day
Rejections happen to every vendor, including good ones. What matters is how fast and how completely you fix them. Read the notice in full, fix exactly what it asks for — replacement photos, a corrected report answer, a revised bid — and resubmit the same day. A QC response is usually a same-day fix, provided you read the whole request instead of guessing.
Photo Documentation That Gets Approved
MCS reviewers approve orders on the strength of the photo set. The discipline that gets orders approved is the same across the national platforms — build it into a habit on every MCS order:
- Before, during, and after — every task. A before shot from a wide angle, a during shot showing the work happening, and an after shot from the same position and angle as the before shot. A reviewer who can compare the two frames does not need to call you.
- Date-stamped, at the property. Take the photos at the property, in the field app or system the order came through, while you are there. Photos pulled from a camera roll later raise the question every reviewer asks: was this taken at this property, on this visit?
- Measured quantities, photographed. Dimensions, cubic yards of debris, linear feet of edging — photograph the measurement in frame. A bid quantity with a photograph behind it survives review; a number on its own does not.
- Photos matched to the report. Every photo labelled to the task it supports, and the report’s condition answers consistent with what the photos show.
- The secure documented properly. On securing orders, photograph the new lock and its key code where required, every locked window and door, and the winterization work if it was part of the order. A secure with no lock photos is an unproven secure.
A photo set that proves the condition you reported protects the order — and the next order on that property too.

Bids: What MCS Reviewers Actually Check
Bidding is where vendors lose the most money on national-platform work, and MCS is no exception. The defence is documentation, not arguing.
Price to the allowable and to the real scope, not to the number you hope the order is worth. Bid real dimensions measured on site, photograph the measurement in frame, and attach the photo to the line it supports. Bill separate tasks as separate line items, and state the method and the reason in plain language. Our winning property preservation bids guide explains how allowables work, and our RepairBASE vs XactPRM comparison covers the two estimators you will meet across the national platforms.
Remember the MCS-specific rule: when work needed for conveyance condition cannot be completed per the published investor guidelines, the correct move is an estimate — itemised, measured, and photo-backed — not unauthorised work. A bid that says what the property needs, what it will cost, and why the guidelines require the estimate is a bid a reviewer can approve. A bid with no measurements and no photos behind it is the easiest line on the order to cut.
The Winter Angle: Why November Is MCS Season
November is when MCS volume and MCS paperwork collide. Winterization orders surge as servicers rush to protect plumbing before the first hard freeze, and winterization is frequently bundled inside securing orders — so a single visit can carry two scopes, two photo sets, and two documentation requirements. At the same time, snow removal orders start appearing in the northern states, and lawn orders keep running until the ground freezes.
The 7 Mistakes That Get MCS Orders Rejected
- Working outside the authorised scope. A securing order authorises the secure — lock change, lock the windows and doors, winterize, maintain the grounds — and nothing else unless specifically requested. Extra work done without authorisation is work you cannot bill.
- Skipping the guideline check. FHA, VA, USDA, and GSE loans each carry their own published investor guidelines, and the allowable scope follows the loan type.
- Doing the work instead of bidding it. When work needed for conveyance condition cannot be completed per the published investor guidelines, the correct outcome is an estimate.
- Guessing quantities instead of measuring them. Dimensions estimated from a listing photo, quantities without a tape in frame. A reviewer who cannot verify the number will not approve it.
- A photo set that does not match the report. Photos that contradict the condition answers, missing before-or-after pairs, or photos taken off-site. The report and the photos are one record — if they disagree, the order comes back.
- Marking the order complete before the documentation is in. The photos, the report, and the invoice go together. Finish the paperwork first, then complete the order.
- Sitting on a rejection. A QC response is usually a same-day fix. Letting it sit turns a small correction into a late order — and late orders cost you future volume.
Each of these is a process failure, not a skill failure. A fixed sequence — read the scope and the guideline reference, do only the authorised work, photograph it in the app, match the report to the photos, bid with measurements, complete only when everything is in, and clear rejections the same day — prevents all seven.
Who MCS Helps — and What It Costs a Vendor
Used well, MCS is a vendor’s steadiest source of volume: a national network across the US and its territories, a constant flow of securing, debris, lawn, winterization, and snow work, and a conveyance-condition standard that — once learned — makes every order predictable.
The cost is real, though. Every order carries office time — the check-in, photo labelling, report writing, bid follow-up, rejection handling — an hour or more after the fieldwork across a full route. And the guideline rule means the office work is not just typing: someone has to check which loan type the order belongs to and what its guidelines allow before the crew drives out. That is why many vendors split the job — field crews do the work and take the photos, while a back office handles the guideline checks, reports, bids, invoicing, and rejection follow-up. If the MCS paperwork is eating your field hours, work order processing support can take it off your plate — see our services for the pay-per-task model with no contract and no monthly minimums.
FAQ
How do I become an MCS vendor?
MCS works with vendors through its own vendor network — reach out to MCS to complete its vendor application process. Expect the standard vetting every national preservation network applies: an application covering your company, trades, service area, and experience; insurance certificates, with general liability as the baseline; trade licenses where required; a W-9 and payment setup; and a background check, standard for anyone entering vacant properties on behalf of a servicer. Confirm the exact list with your MCS contact during onboarding, and be specific about what you actually do and where you can cover — your coverage map is a promise, not a wish list.
What kinds of work orders does MCS assign?
The standard set: conveyance condition management, securing (lock changes, locking windows and doors, winterization, grounds), debris removal, lawn maintenance including an automatic grass cut program, winterization, and snow removal. MCS also lists discoloration remediation, eviction coordination, insurance claim repairs, pool securing and maintenance, roof repair and replacement, violation resolution, and steel security solutions.
What is conveyance condition, and why does it matter on MCS work?
Conveyance condition is the standard the property must meet for the servicer to convey it — hand it over — under the investor’s rules. MCS’s whole preservation programme points at it: all work required by the regulatory guidelines for each loan type is completed so the property reaches conveyance condition, and where work cannot be completed per the published investor guidelines, an estimate is provided instead.
Which guidelines govern an MCS work order — FHA, VA, or HUD?
The regulatory guidelines for the loan type govern. MCS follows the investor guidelines applicable to each loan — FHA, VA, USDA, or GSE as the case may be — and for loan types with no applicable regulatory guidelines, the HUD guidelines are followed. Check the loan type on the order before you start, because the allowable scope follows it.
What should I do if MCS rejects my order or asks for corrections?
Read the notice in full, fix exactly what it asks for — replacement photos, a corrected report answer, a revised bid — and resubmit the same day. Check first for work done outside the authorised scope, a photo set that does not match the report, or an undocumented bid quantity: those three cause most MCS rejections.
The Bottom Line
MCS rewards vendors who treat the investor guidelines as the job, not an afterthought. Learn what conveyance condition means, read the loan type and its guidelines before you drive, do only the work the order authorises, photograph everything at the property so the photo set proves the report, bid with measurements you can defend — and estimate instead of working when the guidelines say so — and clear rejections the same day. That sequence is the difference between an order approved the first time and one that comes back for rework.
If the MCS paperwork — guideline checks, reports, photo labelling, bids, invoicing, rejection follow-up — is slowing your crews down, AssetSure Processing can help. We have processed 67,200+ work orders since 2013 with 99.8% QC compliance, under-one-hour turnaround, and 24/7 coverage, across PPW, Pruvan, MCS, ServiceLink, Cyprexx, and Altisource, on a pay-per-task basis with no contract and no monthly minimums. See our pricing to check the fit for your volume.
